Roller chain or bush roller chain is the type of chain drive most commonly used for transmission of mechanical power on many kinds of domestic, industrial and agricultural machinery, including conveyors, wire- and tube-drawing machines, printing presses, cars, motorcycles, and bicycles. It consists of a series of short cylindrical rollers held together by side links. It is driven by a toothed wheel called a sprocket. It is a simple, reliable, and efficientAs much as 98% efficient under ideal conditions, according to means of power transmission.
Sketches by Leonardo da Vinci in the 16th century show a chain with a roller bearing. In the 16th century, Leonardo da Vinci made sketches of what appears to be the first steel chain. These chains were probably designed to transmit pulling, not wrapping, power because they consist only of plates and pins and have metal fittings. However, da Vinci's sketch does show a roller bearing. In 1800, James Fussell patented a roller chain on development of his balance lock and in 1880 Hans Renold patented a bush roller chain.
Construction
There are two types of links alternating in the bush roller chain. The first type is inner links, having two inner plates held together by two sleeves or bushings upon which rotate two rollers. Inner links alternate with the second type, the outer links, consisting of two outer plates held together by pins passing through the bushings of the inner links. The "bushingless" roller chain is similar in operation though not in construction; instead of separate bushings or sleeves holding the inner plates together, the plate has a tube stamped into it protruding from the hole which serves the same purpose. This has the advantage of removing one step in assembly of the chain.
The roller chain design reduces friction compared to simpler designs, resulting in higher efficiency and less wear. The original power transmission chain varieties lacked rollers and bushings, with both the inner and outer plates held by pins which directly contacted the sprocket teeth; however this configuration exhibited extremely rapid wear of both the sprocket teeth and the plates where they pivoted on the pins. This problem was partially solved by the development of bushed chains, with the pins holding the outer plates passing through bushings or sleeves connecting the inner plates. This distributed the wear over a greater area; however the teeth of the sprockets still wore more rapidly than is desirable, from the sliding friction against the bushings. The addition of rollers surrounding the bushing sleeves of the chain and provided rolling contact with the teeth of the sprockets resulting in excellent resistance to wear of both sprockets and chain as well. There is even very low friction, as long as the chain is sufficiently lubricated. Continuous, clean, lubrication of roller chains is of primary importance for efficient operation, as is correct tensioning.
Lubrication Many driving chains (for example, in factory equipment, or driving a camshaft inside an internal combustion engine) operate in clean environments, and thus the wearing surfaces (that is, the pins and bushings) are safe from precipitation and airborne grit, many even in a sealed environment such as an oil bath. Some roller chains are designed to have o-rings built into the space between the outside link plate and the inside roller link plates. Chain manufacturers began to include this feature in 1971 after the application was invented by Joseph Montano while working for Whitney Chain of Hartford, Connecticut. O-rings were included as a way to improve lubrication to the links of power transmission chains, a service that is vitally important to extending their working life. These rubber fixtures form a barrier that holds factory applied lubricating grease inside the pin and bushing wear areas. Further, the rubber o-rings prevent dirt and other contaminants from entering inside the chain linkages, where such particles would otherwise cause significant wear.
There are also many chains that have to operate in dirty conditions, and for size or operational reasons cannot be sealed. Examples include chains on farm equipment, bicycles, and chain saws. These chains will necessarily have relatively high rates of wear.
Many oil-based lubricants attract dirt and other particles, eventually forming an abrasive paste that will compound wear on chains. This problem can be reduced by use of a "dry" PTFE spray, which forms a solid film after application and repels both particles and moisture.
Motorcycle chain lubrication Chains operating at high speeds comparable to those on motorcycles should be used in conjunction with an oil bath.Chains operating at high speeds comparable to those on motorcycles should be used in conjunction with an oil bath, according to: Lubrecht, A. and Dalmaz, G., (eds.) Transients Processes in Tribology, Proc 30th Leeds-Lyon Symposium on Tribology. 30th Leeds-Lyon Symposium on Tribology, 2–5 September 2003, Lyon. Tribology and Interface Engineering Series (43). Elsevier, Amsterdam, pp. 291–298. For modern motorcycles this is not possible, and most motorcycle chains run unprotected. Thus, motorcycle chains tend to wear very quickly relative to other applications. They are subject to extreme forces and are exposed to rain, dirt, sand and road salt.
Motorcycle chains are part of the drive train to transmit the motor power to the back wheel. Properly lubricated chains can reach an efficiency of 98% or greater in the transmission. Unlubricated chains will significantly decrease performance and increase chain and sprocket wear.
Two types of aftermarket lubricants are available for motorcycle chains: spray on lubricants and oil drip feed systems. Spray lubricants may contain wax or PTFE. While these lubricants use tack additives to stay on the chain they can also attract dirt and sand from the road and over time produce a grinding paste that accelerates component wear. Oil drip feed systems continuously lubricate the chain and use light oil that does not stick to the chain. Research has shown that oil drip feed systems provide the greatest wear protection and greatest power saving.Oil drip feed provided the greatest wear protection between chain roller and pin, Oil drip feed provided the greatest power saving over unlubricated chains and sprockets, according to Lee, P.M. and Priest, M. (2004) An innovation integrated approach to testing motorcycle drive chain lubricants. In: Lubrecht, A. and Dalmaz, G., (eds.) Transients Processes in Tribology, Proc 30th Leeds-Lyon Symposium on Tribology. 30th Leeds-Lyon Symposium on Tribology, 2–5 September 2003, Lyon. Tribology and Interface Engineering Series (43). Elsevier, Amsterdam, pp. 291–298.
Variants
If the chain is not being used for a high wear application (for instance if it is just transmitting motion from a hand-operated lever to a control shaft on a machine, or a sliding door on an oven), then one of the simpler types of chain may still be used. Conversely, where extra strength but the smooth drive of a smaller pitch is required, the chain may be "siamesed"; instead of just two rows of plates on the outer sides of the chain, there may be three ("duplex"), four ("triplex"), or more rows of plates running parallel, with bushings and rollers between each adjacent pair, and the same number of rows of teeth running in parallel on the sprockets to match. Timing chains on automotive engines, for example, typically have multiple rows of plates called strands.
Roller chain is made in several sizes, the most common American National Standards Institute (ANSI) standards being 40, 50, 60, and 80. The first digits indicate the pitch of the chain in eighths of an inch, with the last digit being 0 for standard chain, 1 for lightweight chain, and 5 for bushed chain with no rollers. Thus, a chain with half-inch pitch is a No. 40 while a No. 160 sprocket has teeth spaced 2 inches apart, etc. Metric pitches are expressed in sixteenths of an inch; thus a metric No. 8 chain (08B-1) is equivalent to an ANSI No. 40. Most roller chain is made from plain carbon or alloy steel, but stainless steel is used in food processing machinery or other places where lubrication is a problem, and nylon or brass are occasionally seen for the same reason.
Roller chain is ordinarily hooked up using a master link (also known as a "connecting link"), which typically has one pin held by a horseshoe clip rather than friction fit, allowing it to be inserted or removed with simple tools. Chain with a removable link or pin is also known as "cottered chain", which allows the length of the chain to be adjusted. Half links (also known as "offsets") are available and are used to increase the length of the chain by a single roller. Riveted roller chain has the master link (also known as a "connecting link") "riveted" or mashed on the ends. These pins are made to be durable and are not removable.
Horseshoe clip A horseshoe clip is the U-shaped spring steel fitting that holds the side-plate of the joining (or "master") link formerly essential to complete the loop of a roller chain. The clip method is losing popularity as more and more chains are manufactured as endless loops not intended for maintenance. Modern motorcycles are often fitted with an endless chain but in the increasingly rare circumstances of the chain wearing out and needing to be replaced, a length of chain and a joining link (with horseshoe clip) will be provided as a spare. Changes in motorcycle suspension are tending to make this use less prevalent.
Common on older motorcycles and older bicycles (e.g. those with hub gears) this clip method cannot be used on bicycles fitted with derailleur gears, as the clip will tend to catch on the gear-changers.
In many cases, an endless chain cannot be replaced easily since it is linked into the frame of the machine (this is the case on the traditional bicycle, amongst other places). However, in some cases, a joining link with horseshoe clip cannot be used or is not preferred in the application either. In this case, a "soft link" is used, placed with a chain riveter and relying solely on friction. With modern materials and tools and skilled application this is a permanent repair having almost the same strength and life of the unbroken chain.
Use
Roller chains are used in at around 600 to 800 feet per minute; however, at higher speeds, around 2,000 to 3,000 feet per minute, V-belts are normally used due to wear and noise issues. A bicycle chain is a roller chain. Bicycle chains may have a master link, or may require a chain tool for removal and installation. A similar but larger and thus stronger chain is used on most motorcycles although it is sometimes replaced by either a toothed belt or a shaft drive, which offer lower noise level and fewer maintenance requirements. A timing chain is a roller chain used in some internal combustion automobile engines to drive a camshaft. Very high performance engines often use gear drive, and starting in the early 1960s toothed belts were used by some manufacturers.
The Harrier jump jet uses a roller chain driven by an air motor to rotate its engine nozzles to create its unique "thrust vectoring" propulsion, which point downwards for hovering flight, and to the rear for normal forward flight.
Leaf chain A is similar to but not the same as a roller chain. Leaf chains resemble roller chains, and are used in: Forklifts as a pulley to raise and lower their fork carriage Chainsaws as cutting chains, which superficially resemble roller chains but are more closely related to the leaf chain. They are driven by projecting drive links which also serve to locate the chain onto the bar.
Wear